- 281
- 327 552
Stan
Приєднався 31 тра 2008
Videos
Відео
2023 Ocean City - Kite Festival
Переглядів 5810 місяців тому
Time-lapse Audio- Moldy Lotion by Light-foot soundcloud.com/light-foot Creative Commons - Attribution 3.0 Unported- CC BY 3.0 Free Download / Stream: bit.ly/moldy-lotion Music promoted by Audio Library ua-cam.com/video/GSSdXximD7c/v-deo.html
Baby snapping turtles
Переглядів 492 роки тому
Dug up a ton of snapping turtle egg's moving some piles of dirt. Let them hatch and released back where they were found
Mossy Oak Gamekeeper Feeder
Переглядів 8663 роки тому
Mossy Oak Gamekeeper 200lb Capacity Steel Deer Feeder. 10 second run with corn
Milwaukee old school m12 impact vs. M18 suge impact
Переглядів 254 роки тому
Milwaukee old school m12 impact vs. M18 suge impact
Geeze… I’m never lifting my truck.
So is this a bad thing ?
When it gives you a blood blister, I'd say so
2 washers
Love it. Short and to the point. (Unlike so many other vids). Thanks!!
Gzui
Or rolled up electrical tape?
Piece of HDPE plastic shaped to fit
@@floggerSG idk what that is bro help
Is that velcro?
Do you know how to fix these boards? Mine wont load the program. Tried different disk and floppy drive.
No, sorry
Buy a 570 model end nozzle and put it on the 580 for snow and wet leaves. The airspeed increases dramatically.
metal ASMR.
Disculp como lo arreglaste ???
definetly a needed fix, my loose mag drives me nuts, thanks what's up with the sound? is it me? probably
Shoot it enough you'll build a callous. Problem solved and it will show you're dedicated to the platform.
I shouldn’t have to spend 600 dollars on a half ass made pistol to “build a callous” the sig 365 is all around a better purchase compared to my hellcat
Same thing on my 09 Tacoma with 33's and a 3 inch lift all around. Thought it may be the carrier bearing but after doing a full driveline service (carrier bearing, regreasing slip yoke, and replacing all 3 U-joints) it is still there. I think it may be a structural issue and the cross member that the carrier bearing sits on needs additional support.
I believe you have to install shims on your carrier bearing bracket to compensate for the lift and to re angle the drive shaft.
How much?
Its been sold for almost 8 years...
You need the Oem Spicer or Dea carrier bearing, no aftermarket
also, weak rear leaf spring packs, replace them with a stronger/ better aftermarket set. check the angles/geometry, install shims if needed.
Weak carrier bearing crossmember and two piece driveshaft, reinforce the crossmember. or remove the carrier bearing crossmember and two piece driveshaft and replace it with Tom Woods drive shaft.
Tom Woods driveshaft....that is the answer.
@@snowhiterover yeah and you will get noticeable differences in more torque out put vs the two piece shaft.
Light Armor 100, Speech 25, Sneak 50. "My cousin's out fighting dragons, and what do I get? Guard duty."
why do I have this in my recommandations
Thats a really good question
same
Recommandations. Yes. That's why i'm here.
Mine wobbles the same amount, even when loaded. Feeds fine, just bothersome.
WHOA!!!!!!!! 🤷♂️
Clowns to the left of me and Jokers to the right
I hope this is your back porch because it be dirty at your crib
Scrawny
0:16 hot-teens24.online
I agree that this is not the best method, especially filming one handed in portrait mode. But the guy is literally trying to help people and you tear him down for it? If you need to be an ass, go tear down someone’s video that has 1million views. You obviously tried to find a video with 1million views but couldn’t, this guy was all you kind find with your search.
This was just as stupid as the last video😂😂😂
floggerSG okay 🙄
Lmao shoving a piece of plastic in the magwell and calling it a mod. Whats gonna be funny as hell is when u go to reload and your plastic goes up and not the mag.
What a clown.
Thats exactly what i would do is shove a big piece of random plastic up my new hellcats magwell lmao. Goodluck with that. Even your ducks was laughing.
Hahahaha!
If that "random plastic" was sold by glockstore or wilson combat your bitch ass would be ordering one for every gun! IF YOU EVEN HAVE A GUN
@@throatpunch4789thats alot talk for a little puss behind a computer screen. Btw if u owned one you would know better also dipshit.
@@centermass4962 i have a hellcat and the mag is loose too thats what brought me to this video and what is so wrong with trying to stop your mag from wobbling? NOTHINGS wrong with it, like you said you just wanted to be a little pussy talking shit behind your screen
@@throatpunch4789 i said it wasnt a good idea. I did t call the dude names u bitchmade little punk. And btw i own a hellcat also
Exciting! What In life is beautiful to you? Let's build Each other Up Xd
What a stupid video. Thank god it was only 18 seconds. Do you cry when your Cheerios get soggy
you must not really have a clue
Man i have a 13 yr old son that has shot the hell out of my hellcat and never said one time its pinched his finger. He has smaller hands than me. I dont understand how u r getting your finger between the mag and gun. It dont wobble loaded.
Load it full of ammo. It won't wobble.
Emmy award winning video right there
Lmao.
Pretty cool setup! Can you show a video of the installed? How is that attached to your truck. Im interested in the part that is bolted to your truck.
@@floggerSG k thanks.
Are you still using the machine's original power supply? The power supply on my K111 died last week. I'm wondering if it's as easy as buying any power supply with the same output voltages, and hooking it all up. Or does it require something more fancy.
hola floggersSG, que tal, como va todo, queria comentarte, ya hice todo tal como esta en tu tutorial, pero nada que me deja ver pantalla completa, me aparece siempre imagenes del logo HUNTER distorcionadas, gracias, un saludo
Same here I have two spectra plastic fuel tanks same as yours. Mine are red. I’m looking for the same sort of mount set up but can’t find anywhere. The ones for the metal can says it won’t work with the spectra fuel cans.
Looks like your truck is a Tacoma bed. I have a 17 Tundra.
Ahh you made them yourself?
Where did you get this set up from. I have two Spector and this water container plus have a pick up like this to mount on. Any help would be great.
hola amigo soy de colombia como puedo contactar a el tecnico deseo comprar una tarjeta de k111
That cross member needs to be Rene forced my friend did it and it fixed the problem
This video is old now but wondering was this to demonstrate the way to upgrade the screen on this machine?
How did you get the bracket to go in the rail?